condor d.c. power supplies, inc., a subsidiary of sl industries, inc. 805-486-4565 ?(800) 235-5929 fax: (805) 487-8911 http://www.condorpower.com the smallest most capable 1000 w power supply of its kind. when used with external or-ing diodes, nmx series power supplies can easily be configured as multiple-output, current-sharing, redundant power sys- tems. nmx series switching power sup- plies have power factor correction, 1000- watt multiple output, and current sharing. they are available as low-profile, self- cooled modules, and are designed to meet global requirements. model pwr output #1 output #2 output #3 output #4 nmx-1003-0512 1000 +5v @ 150a +12v @ 20/30a pk -12v @ 10a nmx-1004-1203 1000 +5v @ 150a +12v @ 20/30a pk -12v @ 10a 3.3v @ 10a nmx-1004-1205 1000 +5v @ 150a +12v @ 20/30a pk -12v @ 10a 5v @ 10a nmx-1004-1212 1000 +5v @ 150a +12v @ 20/30a pk -12v @ 10a 12v @ 10a nmx-1004-1224 1000 +5v @ 150a +12v @ 20/30a pk -12v @ 10a 24v @ 5a nmx-1004-1512 1000 +5v @ 150a +15v @ 20/30a pk -15v @ 10a 12v @ 10a nmx-1004-1524 1000 +5v @ 150a +15v @ 20/30a pk -15v @ 10a 24v @ 5a standard nmx series NMX-1000 featuring: forced current sharing for n +1 redundancy remote sense on outputs #1, 2 and 3 ?ero wire?slope program current sharing on outputs #2 and 3 for redundancy universal ac input 0.99 power factor mag-amp regulators eliminate interaction between logic and auxiliary outputs compact, low-profile package, only 12?x 8?x 3.38 dc power good and ac power fail signals true remote inhibit 1000 watts power factor corrected multiple output, forced current sharing
condor d.c. power supplies, inc., a subsidiary of sl industries, inc. 805-486-4565 ?(800) 235-5929 fax: (805) 487-8911 http://www.condorpower.com dimensions: inches millimeters specifications: all models input ac input: 90-264 vac continuous range, 47 to 63 hz. internally fused for 20 a. power factor: 0.99 typical at full load. meets en61000-3-2. inrush: cold start ac current is less than 90 a at 115 vac and 180 a at 230 vac. limited by thermistor. brownout protection: holds regulation to 85 vac. holdup time: 20 ms minimum after removal of power at full load. efficiency: 75% typical. ac power fail: provides ttl ??5 ms before output voltage goes out of regulation band upon loss of ac power. output adjustability: all outputs user adjustable ?% minimum. outputs #2 and 3 have factory adjustable preprogrammed slope. line & load reg: outputs #1 and 4 hold ?% over ac input range and 0 to 100% load change. outputs #2 and 3 hold ?% (preprogrammed slope). output #1 requires minimum load of 10%. ripple & noise: less than 1% p-p or 100 mv, whichever is greater. remote sense (outputs #1, 2, and 3) : compensates for 250 mv total line drop. open sense lead protection. temperature coefficient: 0.02% per degree c. stability: 0.1% over 8 hours after 30 minutes warm-up. transient response (output #1) : output voltage returns to within 1% in less than 500 ? for a 50% load change. peak transient does not exceed 5%. overload protection: all outputs are protected against overload and short circuit. automatic recovery upon removal of fault. overvoltage protection (outputs #1, 2, and 3) : protects load against power supply induced overvoltage. trip point is factory set so that output voltage cannot exceed 136% of nominal. peak output current: dual current ratings define continuous and peak currents. the peak current shown can be delivered for a maximum period of 30 seconds. remote inhibit: contact closure to the negative sense line or a ttl level ??turns off dc outputs. dc power good: provides a ttl ??when output #1 is above 4.6 v nominal. redundancy: external or-ing diodes and current sharing on outputs #1, 2, and 3 provide ?+1?capability. remote senses compensate for additional 0.6 v diode voltage drop. when the forced current sharing terminal is connected among units, current sharing remains within 10% of the unit s full output current rating. environmental thermal protection: shuts down power supply if overheated. automatic recovery. temperature range: 0 to 50? at full ratings. safety agencies: most models are approved to ul1950; csa 22.2 #234; iec 950 and t?v en60950, class 1 selv., ce 72/23/eec/93/68eec (low voltage directive). conducted rfi: meets fcc part 15, subpart j, class a; en55022 class b; cispr 22 class b. output isolation: isolated from ground 50 vdc. function 115 vac 230 vac connector tb1- line line 1 tb1- neutral line 2 tb1- safety ground safety ground ac input (90-264 vac continuous range) function location notes connector output #1 terminal marked +v main output terminal marked -v rtn (common) output #2 j2-1, 2, 3 j2-4, 5, 6 rtn (common) output #3 j2-7, 8, 9 j2-4, 5, 6 rtn (common) output #4 j2-10, 11, 12, (+) floating output j2-13, 14, 15 (-) floating output dc output amp # 350830-1 mates with plug housing # 350736-1 with pins barrier strip # 6-32 screws 3/8?centers function location notes connector remote sense j3-1 output #1 sense j3-3 output #1 sense rtn j3-8 output #2 sense j3-7 output #2&3sense rtn j3-9 output #3 sense dc power good j3-6 reference to common ac power fail j3-4 when a sense rtn is inhibit j3-5 terminated current share j3-2 status and control amp mta type #640456-9 pin header (locking) studs # 5/16-18 x 1 (l) (n) ( ) NMX-1000 10.4 lbs - 4.7 kgs 1000 watts 12 x 8 x 3.38 NMX-1000 reverse voltage: protected against reverse voltage up to supply current rating. cooling: self cooled with internal ball-bearing fans. consult factory for alternative configurations. options: consult factory for available options.
|
